VEX Robotics Sprocket and Chain Kit
- Chain material plastic, chain size 025 in wide. Sprocket od 10t = 526 in | 15t = 75 in | 24t = 118 in | 40t = 193 in | 48t = 23 in. Chain and sprocket pitch 01475 in. Master link 326 total, center hole size 0125 in square. Length 2 preassembled chains of 163 links each, total of 48 in.
VEX Robotics Design System Transmitter and Receiver Add-On Kit
- Allows you to have two human operators control different functions of the same robot. This kit includes a vex 75mhz transmitter and receiver pair. List of contents 1 trasmitter unit 1 transmitter frequency module, channel 89 1 rf receiver module 1 receiver crystal, channel 89 1 receiver antenna sleeve 1 receiver antenna sleeve holder 5 keps nuts 5 8-32 x 3/8″ screws 1 9″ rj-10 cable, interconnect between the rf receiver module and vex micro controller 1 inventor’s guide insert. Technical info control frequency channel 89, 75. Will not interfere with the channel of your vex starter kit. Adds functionality to your vex robot by adding new possibilities. 970 mhz tx battery type 8 aa batteries (not included), or vex robotics power pack number of channels 6 (4 analog and 2 digital) analog channels 2 potentiometers, each with an x and y axis digital channels 4 momentary switches (located on the backside) tx size 8 x 8 x 2. Provides the radio control link which allows human operators direct control of a vex robot. Rx weight 0. 5 in. Tx weight 1. 63 lbs. Transmitter is a 6-channel (4-analog, 2-digital) hobby grade fm unit, custom configured for vex. 05 lbs.
VEX Robotics High Strength Sprocket and Chain Kit
- 57in. Wide mounting holes 0. Wide, attatchment links are 1. 175in. Also use included “attachment links” to attach structural components to your chain. This kit provides larger size chain and sprockets designed for use with the vex robotics design system. These reinforced sprockets and chain can be used just like the vex sprocket and chain kit but can withstand higher stresses and lift heavier loads. Chain width links are 0. Use this kit for any application where regular chain just won’t cut it technical info material type delrin plastic master links every link can act as a master link to make chains of any length tensile strength approximately 50 lbs. Diameter. The components from this kit are compatible with all vex tank tread components. 5in. Vex high strength chain is the same pitch as vex tank tread. Chain length 140 links = 54in.
VEX Robotics Smart Charger v2
- 59 grams) power cord 0. 162 lbs (73. 6v batteries charges both nicd and nimh batteries includes dual charge rates and an automatic shutoff input voltage ac 100-240v output voltage 20vdc weight smart charger 0. 48 grams) actual weight of one item (no packaging). 2v and 9. The vex smart charger v2 is capable of charging all vex rechargeable power packs. 526 lbs (238. Charges both 7.
VEX Robotics Rack Gear (16-pack)
- Use any vex spur gear as a pinion to drive these rack gears. Each rack gear includes (3) 6-32 threaded inserts on their back face mount these similar to vex motors or servos with 6-32 screws. Stack multiple rack gears back to back for longer motions. Combine these with a vex linear slide and rack gear bracket (sold separately) to create a simple linear actuator.
VEX Robotics Bevel Gearbox Bracket, 2-pack
- Material finish zinc plated. Material type cold rolled steel per astm a-1008 cs type b (approx 40ksi tensile strength). Material thickness 0046in (117mm). Hole size 0182 square (vex standard). Kit contents 2 bevel gearbox brackets (no gears included).
VEX Robotics Light Sensor Kit
- With the light sensor, you can program a whole new range of capabilities to your robot. Design a simple tracker that follows the beam of a flashlight, or use a light sensor to help your robot to avoid getting stuck under furniture by making it steer away from shadows. The light sensor uses a photocell that allows your robot to detect and react to light. You can even give your robot color vision by putting colored filters on different light sensors a programming kit is needed to change the program in the vex controller.
VEX Robotic Spider
- The led module will change color with every turn of the spider�s head. Motors receive signals from the brain, spinning into action, causing the head to rotate and the legs to cycle. The distance sensor reflects infrared light, which alerts the spider before it crashes into its surroundings. The brain is the centralized computer that powers the spider, relaying signals from the remote control, and activating the motors and sensors to bring the spider to life.
VEX Robotics Wheel Leg Kit (Whegs), 4-pack
- Square. 30 inches leg material abs plastic foot material soft rubber weight 0. Each kit comes with (4) wheel legs. They are great for constructing all-terrain or off-road robots. 074 lbs per wheel center hole size 0. Create robots capable of climbing over almost any obstacle with the vex 6″ wheel legs. These legs consist of (4) spoke “legs” protruding from a central hub. 125 in. Technical info wheel diameter 6 inches (approximate max diameter) leg and foot thickness 0.
VEX Robotics 2000mAh 7.2V NiMH Robot Battery
- Standard vex power connector. Capacity 2000 mah. Rechargeable nickel metal hydride (nimh). Use with any vex microcontroller (v05 pic, cortex or vexpro arm9) charge with the vex smart charger.
VEX Robotics Servo Kit by VEX Robotics
- Replacement gears, 1cm shaft and mounting hardware are included. • servo motor specifically designed for the vex robotic kits • mounting hardware and replacement gears included • 100 degrees of rotation the vex servo motor is the ideal solution where partial motion or rotation is necessary. The output shaft matches with the square cross-section of vex shafts and two parallel mounting holes allow you to connect to easily to your robot.
HEXBUG VEX Robotics Ant
- The vex robotics ant includes 6 wheels, dual bump sensors and interlocking gears. Design, build and drive this giant-sized hexbug from the ground up with vex robotics. This kit is cross-compatible with other hexbug vex robotics kits. Drive manually with the remote control or program it to wander autonomously, mimicking real-life behavior.
VEX Robotics Spacer Variety Pack
- Eliminate slop on shafts. Plastic and nylon. Nylon spacers contain ten (10) each of 0125″, 0250″, 0375″, and 0500″ for a total of 40 spacers. Add space between metal parts.
VEX Robotics Metal C-Channel 1x2x1x35 Holes, 2-pack
- 500″ increments. Includes two (2) lengths of 17. 50in. This structural member is perfect for building bigger robots. 046″ thick, zinc plated. 500″ increments. Vex c-channel has holes on 0. 5″ pieces. Excellent strength and twist resistance. Can be cut on 2. Made from cold rolled steel, 0. Cuttable each channel is segmented into cuttable 2.
VEX Robotics Worm Gearbox Bracket, 2-pack
- (1. This is the simplest way to mount and utilize the worm gears. 17mm) material finish zinc plated hole size 0. Kit includes two worm gear brackets. 182 square (vex standard). This bracket is designed with the vex worm gear. 046in. Kit contents 2 worm gearbox brackets material type cold rolled steel per astm a-1008 cs type b (approx 40ksi tensile strength) material thickness 0. No gears are included.
VEX Robotics Rack Gearbox Bracket, 2-pack
- No gears are included. Use additional standard vex motion products (not included) to utilize this bracket with the vex rack gear. . This bracket is designed with the vex rack gear in mind. Kit includes two gear brackets. An application of this bracket and the rack and pinion gear uses the pinion gear to rotate the rack gear which will in turn slide linearly using the vex linear slide pack. This allows users to create linear motion.
Vex Robotics Optical Shaft Encoder Kit
- The optical shaft encoder can be used to track distance traveled, direction of motion, or position of any rotary component, such as a gripper arm. Input function start signal to the ultrasonic sensor. Output function echo response from the ultrasonic sensor. Frequency 40 khz.
VEX Robotics 8mm Spacer, 20-pack
- Height 0. Hole 0. 194in. 330. A spacer is used to create a space between two objects, often to properly position them. 500in. Eliminate slop on shafts add space between metal parts plastic and nylon diameter 0. In.
