16 Greatest Brushless Escs

 

YoCoo 2-4S 30AMP SimonK Firmwar Brushless ESC Speed Controller w 3A 5V BEC for DJI Phantom RC Quadcopter ESC Part Pack of 2 #ad

YoCoo 2-4S 30AMP SimonK Firmwar Brushless ESC Speed Controller w/ 3A 5V BEC for DJI Phantom RC Quadcopter ESC Part (Pack of 2)

YoCoo 2-4S 30AMP SimonK Firmwar Brushless ESC Speed Controller w/ 3A 5V BEC for DJI Phantom RC Quadcopter ESC Part (Pack of 2) #ad - Continue current 30a, burst current 40a up to 10s. 16khz motor frequency, giving fastest response of the motor, and quietest operation as well (no 8khz squeal). Super high refresh rate, no buffering of the input signal, resulting in more than 490hz response rate . Highest efficiency 100% n-fet design and highest accuracy with crystal oscillator (temperature won’t affect the pwm operating range like other cheap esc’s). Ultra high refresh rate, no buffering of the input signal, resulting in more than 490hz response rate.

 

E-flite 30-Amp Pro Switch-Mode BEC Brushless ESC V2 #ad

E-flite 30-Amp Pro Switch-Mode BEC Brushless ESC (V2)

E-flite 30-Amp Pro Switch-Mode BEC Brushless ESC (V2) #ad - 5mm gold bullet connectors on motor output leadsoverviewthe e-flite® 30-amp pro switch-mode bec brushless esc (v2). It can operate without the need for a separate receiver battery to power your servos and receivers, saving you weight and complication. 5a continuous current, 5v switch-mode bec circuitstronger bec for support of most 3-axis stabilization systemsdrive up to 7 analog or 6 digital standard-size servos with the bec3- to 4-cell li-po, 9- to 12-cell ni-mh/ni-cd input voltageprogrammable motor brakingsafe power-arm mode prevents accidental startsprogrammable low voltage cutoff with settings for 3-cell li-po (9. 8ms)programmable soft start for helis and airplanesauto motor shut down if signal is lost or there is interferenceprogrammable timing, 5 user-selectable ranges for use with a large variety of brushless motorspre-wired connectors-e-flite ec3tm connector on battery input and 3. 1ms-1. 2v), 4-cell li-po (12v) or 74% of battery starting voltageprogrammable throttle input range (1. 9ms or 1. This is a high-quality sensorless brushless electronic speed control with an integrated switch-mode bec that is very lightweight and efficient. 2ms-1. Key featuresup to 30 amps continuous current with proper air flow and 35 amps burst current (15 seconds)3.

 

RCmall XXD A2212 1000KV Brushless Motor with 30a Brushless ESC1045 Propeller Props for DJI F450 550 #ad

RCmall XXD A2212 1000KV Brushless Motor with 30a Brushless ESC+1045 Propeller Props for DJI F450 550

RCmall XXD A2212 1000KV Brushless Motor with 30a Brushless ESC+1045 Propeller Props for DJI F450 550 #ad - Dji f450 f550 tarot fy450 fy550 quadcopter fpv part. Brushless motor a2212/13 kv1000 for airplane aircraft quadcopter. 30a brushless esc and pair 1045 propeller. Package included1 x a2212 1000kv brushless motor,1 x 30a brushless esc,2 x 1045 propeller with screws. If any questions, please do not hesitate to contact us and we will try our best to help you .

 

6PCS ARRIS 2-6S 30AMP 30A SimonK firmware OPT Brushless ESC for RC Quad Multicopter #ad

6PCS ARRIS 2-6S 30AMP 30A SimonK firmware OPT Brushless ESC for RC Quad Multicopter

6PCS ARRIS 2-6S 30AMP 30A SimonK firmware OPT Brushless ESC for RC Quad Multicopter #ad - The most significant feature of arris simonk 30a brushless esc is that it has 400mm singnal wire and power cord, no need to add extra wires, which greatly reduce the triviality in wiring. Specification, weight 25g, size 55 19 10mm, continuous current 30a, burst current 45a , bec mode opto, the applicable number of battery cells 2-6s package includes 6 x arris 30a opto brushless esc copy this link to your broswer to download the manual http//site. Pdf. Suitable for multirotor aircraft. Hobby-wing. Com/images/manual/arris-esc-user-manual.

 

E-flite 40 AMP Brushless ESC #ad

E-flite 40 AMP Brushless ESC

E-flite 40 AMP Brushless ESC #ad - Size l 193″ (49mm), w 148″ 38mm), h 079″ (20mm). Weight 196 oz, 555 g. Reversible yes, with lockout. 40 amp brushless esc. Operating environment waterproof design allows for use in nearly any environment.

 

E-flite 60-Amp Pro Switch-Mode BEC Brushless ESC V2 #ad

E-flite 60-Amp Pro Switch-Mode BEC Brushless ESC (V2)

E-flite 60-Amp Pro Switch-Mode BEC Brushless ESC (V2) #ad - Key featuresup to 60 amps continuous current with proper air flow and 75 amps burst current (15 seconds)5a continuous current, 5v switch-mode bec circuit (proper cooling and airflow required)stronger bec for support of most 3-axis stabilization systemsdrive up to 7 analog or 6 digital standard-sized servos with the bec on any recommended input voltage3- to 6-cell li-po, 9- to 18-cell ni-mh/ni-cd input voltagefinned heat sinksprogrammable motor brakingsafe power-arm mode prevents accidental startsprogrammable low voltage cutoff with settings for 3-cell li-po (9v), 4-cell li-po (12v), 5-cell li-po (15v), 6-cell li-po (18v) or 74% of battery starting voltageprogrammable throttle input range (1. 9ms or 1. 5mm gold bullet connectors on motor output leadsoverviewthe e-flite® 60-amp pro switch-mode bec brushless esc (v2). 1ms-1. 2ms-1. It can operate without the need for a separate receiver battery to power your servos and receivers, saving you weight and complication. This is a high-quality sensorless brushless electronic speed control with an integrated switch-mode bec that is very lightweight and efficient. 8ms)programmable soft start for helis and airplanesauto motor shut down if signal is lost or there is interferenceprogrammable timing-5 user-selectable ranges for use with a large variety of brushless motorsutilizes new smaller mosfet technology to minimize weightradio system power on/off switchpre-wired connectors-e-flite® ec3tm connector on battery input and 3.

 

RioRand F-20A 20AMP 20A SimonK Brushless ESC w 3A 5V UBEC quadcopter APM2 #ad

RioRand® F-20A 20AMP 20A SimonK Brushless ESC w/ 3A 5V UBEC quadcopter APM2

RioRand® F-20A 20AMP 20A SimonK Brushless ESC w/ 3A 5V UBEC quadcopter APM2 #ad - Powered by riorand advanced technology. Max efficiency current 4-10a (>75%). Shaft diameter Φ317mm. Motor dimensions Φ275 x 30mm.

 

GoolRC Hobbywing SkyWalker 60A Brushless ESC Electric Speed Controller RC With UBEC #ad

GoolRC Hobbywing SkyWalker 60A Brushless ESC Electric Speed Controller RC With UBEC

GoolRC Hobbywing SkyWalker 60A Brushless ESC Electric Speed Controller RC With UBEC #ad - Regardless the throttle stick position, the motor will not spin after battery connected. Hobbywing skywalker 60a brushless esc speed controller with ubec. Low voltage cutoff protection / over-heat protection / throttle signal lost protection. Maximum speed 210000 rpm (2 poles motor), 70000 rpm (6 poles motor), 35000 rpm (12 poles motor). Battery cell 2-6 cells lipo,or 5-18 cells nihh.

 

Redcat Racing Hobbywing Brushless ESC 150A Spare Part #ad

Redcat Racing Hobbywing Brushless ESC 150A Spare Part

Redcat Racing Hobbywing Brushless ESC 150A Spare Part #ad - This item is compatible with the following redcat racing models rampage chimera ep pro, rampage xr-e, rampagexbe. Com to make sure you are purchasing the right part for your vehicle. Redcatracing. Use the parts search at www.

 

GoolRC SKYRC 9T 4370KV Brushless Motor 60A Brushless ESC with 5V2A BEC Linear Mode Program Card Combo Set for 110 RC Car #ad

GoolRC SKYRC 9T 4370KV Brushless Motor & 60A Brushless ESC with 5V/2A BEC Linear Mode & Program Card Combo Set for 1/10 RC Car

GoolRC SKYRC 9T 4370KV Brushless Motor & 60A Brushless ESC with 5V/2A BEC Linear Mode & Program Card Combo Set for 1/10 RC Car #ad - 17mm connector 3. 0125Ω turns 9t length 49mm diameter 35mm shaft length 15mm shaft diameter 3. Features suit for 1/10 scale rc car high rpm precision bearings cnc machined billet t6 aluminum heatsink can high efficient heat transfer with a cooling fan high purity copper windings maximizes conductivity precision engineered for maximum energy conversion do esc programming in a short time and get ready for next run high power and high efficiency combined with low weight and compact dimensions motor specifications brand skyrc volt 4370kv io 2a max current 48a internal resistance 0. 5mm banana plug esc specifications brand skyrc input 2~3s lipo battery, 4~8s nimh battery, 2~3s life battery motor support.

 

ZTW 40A Brushless ESC #ad

ZTW 40A Brushless ESC

ZTW 40A Brushless ESC #ad - The internal bec and low-voltage cutoff settings make it ideal for use with 2s (74v), 3s (111v), or 4s (148v) li-po batteries. Will auto-detect the number of lipo cells in your battery and set the appropriate cut-off voltage without any programming needed. Perfect for mid-size scale, sport or 3d airplanes. A variety enhanced performance and safety features, including super-smooth and accurate throttle linearity, extremely low internal resistance, auto throttle shutdown if signal is lost, thermal overload protection, and more. Includes advanced programming options motor brake, battery type, low voltage cutoff threshold, timing setup, soft start, governor mode, frequency, low voltage cutoff type.

 

E-flite 10-Amp Pro Brushless ESC #ad

E-flite 10-Amp Pro Brushless ESC

E-flite 10-Amp Pro Brushless ESC #ad - 9ms or auto select)auto motor shutdown if signal is lost or there is interferenceprogrammable timing-2 user-selectable ranges for use with a large variety of brushless motorspre-wired connectors-jst on battery input and 2mm female gold bullets on motor output leadssoft startoverviewthis controller has been designed for use in radio control aircraft and to support continuous currents of up to 10 amps when using 2-3 cell li-po battery packs and up to 4 sub-micro servos. . Standard features include advance bec and safe power-arming along with programmable features such as low-voltage cutoff, braking, timing and throttle input range. 1ms-1. Key featuresup to 10-amp continuous current with proper air flowprogrammable motor brakingsafe power-arm mode prevents accidental startsprogrammable low-voltage cutoff with settings for 2-cell li-po (6v), 3-cell li-po (9v) or 70% of battery starting voltageprogrammable throttle input range (1.

 

Goolsky 80A Brushless ESC Electric Speed Controller with 61V3A SBEC for 18 RC Car Truck #ad

Goolsky 80A Brushless ESC Electric Speed Controller with 6.1V/3A SBEC for 1:8 RC Car Truck

Goolsky 80A Brushless ESC Electric Speed Controller with 6.1V/3A SBEC for 1:8 RC Car Truck #ad - Mutiple protection features low voltage cut-off protection for lithium or nickel battery, over-heat protection, throttle signal loss protection, motor blocked protection. Fast response to throttle input. Compatible with sensorless brushless motors. High anti-interference capability. Super smooth and accurate throttle linearity.

 

EMAX Simon Series 12A Brushless ESC Support Simonk Multirotor Parts Black #ad

EMAX Simon Series 12A Brushless ESC Support Simonk Multirotor Parts Black

EMAX Simon Series 12A Brushless ESC Support Simonk Multirotor Parts Black #ad - Quicker throttle response and better throttle linear. Based on simonk firmware, further optimized to the perfect drive performance and can be flashed with blheli firmware. Item simon-12a continuous current 12a burst current(10s) 15a li-xx battery(cell) 2-3 dimension 25207mm weight 9g bec mode linear bec output 1a/5v programmable yes.

 

RioRand 30A Brushless Motor Speed Controller RC BEC ESC #ad

RioRand 30A Brushless Motor Speed Controller RC BEC ESC

RioRand 30A Brushless Motor Speed Controller RC BEC ESC #ad - Current 30a battery range 5-10 cells specification size 57mm x 25mm x 8mm net weight 27g package weight 33g color yellow original box no packing content 1 x 30a speed controller esc. Features bec power yes cut off voltage 4v bec yes bec power 1. 5a/5v reset throttle lowest con.

 

GoolRC 3650 3900KV 4P Sensorless Brushless Motor 60A Brushless Splash-Proof Electronic Speed Controller ESC with 58V3A Switch Mode BEC for 110 RC Car #ad

GoolRC 3650 3900KV 4P Sensorless Brushless Motor & 60A Brushless Splash-Proof Electronic Speed Controller ESC with 5.8V/3A Switch Mode BEC for 1/10 RC Car

GoolRC 3650 3900KV 4P Sensorless Brushless Motor & 60A Brushless Splash-Proof Electronic Speed Controller ESC with 5.8V/3A Switch Mode BEC for 1/10 RC Car #ad - 2mm) laminations 4 poles design, high torque and high efficiency cnc machined 6061 t6 billet aluminum heatsink can precision engineered for maximum energy conversion shorter stator, less wire, lower resistance, more power universal fit all 1/10 brushless cars-multi-mounting system for m3 screwsspecifications kv(rpm/volt) 3900kv max rpm 50000 max current 69a max watts 900w max voltage. Motor features removable/replaceable rotor high rpm abec5 oversized bearings stator, super thin (0.





We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.